View
  • 433telem1-500x500

    ,

    Telemetry 3DR TTL

    The Radio telemetry system base on 3DR Radio system and 100% compatible.

    It’s designed as an open source Xbee replacement radio set, offering a lower price, longer range (approx one mile) and superior performance to Xbee radios. It’s available in 915Mhz and 433Mhz; and in the following configurations: serial board (for the air) and USB (for the ground).

    The system provides a full-duplex link using HopeRF\\\’s HM-TRP modules running custom, open source firmware. Interface to the module is via standard 5V-tolerant TTL serial / FTDI USB serial.

    Firmware upgrades and configuration are fully supported in the APM Mission Planner. Configuration is also possible through the 3DR Radio configurator and AT commands.

    3,800.00
    Add to Cart
  • V03-compatible-Xbee-Arduino-Bluetooh-Bee-Bluetooth-expansion-board-xbee-shield

    ,

    Xbee shield V03

    This shield V03 can achieve a simple two crunodal ZigBee network, achieve wireless communication between Ardu, and allows the Ardu to wireless communicate over a modified ZigBee protocol using the popular XBee module.
    It is a fully Assembled shield without the XBee module. It works with all XBee modules including the Series 1 and Series 2.5, standard and Pro versions.
    850.00
    Add to Cart
  • xcore2530_l_1_2

    ,

    ZigBee XCore2530 1500M

    ZigBee module, features the CC2530F256 onboard, farther communication distance with PA

    Overview

    XCore2530 is a ZigBee module based on CC2530F256.

    Basically this module can be used in two aspects :

    • Develop application with the provided firmware
      Combined with our provided firmware, this is a simple ZigBee wireless UART module, just as easy to use as any other UART module, and requires NO knowledge about the complicate ZigBee Specification
    • Develop your own firmware
      In this case, you should start from the very underlying to create your solution, what’s more, debuggers (like CC Debugger) and knowledge about ZigBee Specification are also required
    1,950.00
    Add to Cart
  • shield3-assembly

    ,

    easyvr shield 3.0 (voice recognition shield)

    EasyVR 3.0 is a multi-purpose speech recognition module designed to add versatile, robust and cost effective speech and voice recognition capabilities to virtually any application.

    EasyVR is the third generation version of the successful VRbot module and builds on the features and functionality of its predecessor.

     

    9,350.00
    Add to Cart
  • I2364742561

    ,

    315/433 RXTX KIT

    This is a transmitter+receiver module avilable at 433 & 315 Mhz. The transmitter Module employs a crystal-stabilized oscillator, ensuring accurate frequency control for best range performance. There is no requirement of external RF components except Antenna.

    145.00
    Add to Cart
  • nrf

    ,

    NRF24L01+

    The nRF24L01+(nRF24L01p) is a single chip 2.4GHz transceiver with an embedded baseband protocol engine (Enhanced ShockBurst™), suitable for ultra low power wireless applications. The nRF24L01+ is designed for operation in the world wide ISM frequency band at 2.400 – 2.4835GHz.
    To design a radio system with the nRF24L01+, you simply need an MCU (microcontroller) and a few exter-nal passive components. The high air data rate combined with two power saving modes make the nRF24L01+ very suitable for ultra low power designs. nRF24L01+ is drop-in compatible with nRF24L01 and on-air compatible with nRF2401A, nRF2402, nRF24E1 and nRF24E2. Intermodulation and wideband blocking values in nRF24L01+ are much improved in comparison to the nRF24L01 and the addition of internal filtering to nRF24L01+ has improved the margins for meeting RF regulatory standards.

    200.00
    Add to Cart
  • cc2530-eval-kit_l_1_2

    , ,

    CC2530 Eval Kit

    CC2530 Eval Kit is a ZigBee development/evaluation kit designed for CC2530F256, consists of the mother board ZB502 and the ZigBee moduleCore2530.

    Basically this kit can be used in two aspects :

    • Develop application with the provided firmware
      Combined with our provided firmware, you can use this kit to set up a minimal ready-to-run ZigBee system for testing or evaluating, and requires NO knowledge about the complicate ZigBee Specification
    • Develop your own firmware
      In this case, you should start from the very underlying to create your solution, what’s more, debuggers (like CC Debugger) and knowledge about ZigBee Specification are also required
    2,200.00
    Add to Cart