View
  • 10dof mems

    10 DOF Mems IMU Sensor

    INTRODUCTION

    At the beginning,the inertial measurement unit is an electronic device that measures and reports on a craft’s velocity, orientation, and gravitational forces, using a combination of accelerometers,gyroscopes, and magnetometers. Now IMUs are commonly used in the Human-computer interaction(HCI), navigational purposes and balancing technology used in the Segway Personal Transporter as we all known.
    The 10 DOF(degrees of the freedom) sensor is a compact and low cost IMU from DFRobot. It integrates the ADXL345 accelerometer, the HMC5883L magnetometer,the ITG-3205 gyro and the BMP085 barometric pressure sensor. It’s suitable for most of the controlling system because of the small dimension. The mounting holes make it possible to provide the highly accurate and stable sensor data.It embeds a low noise LDO regulator for supplying a wide range power input.Works with 3~8 volts power input.Certainly,the 10 DOF sensor is directly compatible with your Arduino boards.

    4,200.00
    Add to Cart
  • 10dofmodule_1

    ,

    10 DOF IMU Sensor

    3 Axis Accelerometer + 3 Axis Gyroscope + 3 Axis Magnetometer + Pressure Sensor on one board i.e.

    ADXL 345+L3G4200D+HMC5883L+BMP085 sensors all in one board. There are also a 2.5V voltage regulator, the logic level converter circuit to make it work under the power of 3V-5V. Thanks to the logic level converter circuit, you can connect it with a 3V-5V MCU directly, just plug and play! Also every interrupt pin of the sensors is leaded out.

    1,850.00
    Add to Cart
  • GY-521_1

    ,

    GY-521 MPU6050 Module 6DOF

    The MPU6050 contains both a 3-Axis Gyroscope and a 3-Axis accelerometer allowing measurements of both independently, but all based around the same axes, thus eliminating the problems of cross-axis errors when using separate devices.

    400.00
    Add to Cart
  • 91450-GY-291-ADXL345-3-Axis-Accelerometer-1200x630w

    ,

    GY-291 ADXL 345

    GY-291 ADXL345 3-Axis Accelerometer is a sensor board based on ADXL345 accelerometer integrated circuit. The ADXL345 is a small, thin, ultralow power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface.

    400.00
    Add to Cart
  • 20150423102824273n548

    ,

    GY-61 ADXL335

    This breakout comes with 3 analog outputs for X, Y and Z axis measurements on a 0.75″x0.75″ breakout board. The ADXL335 is the latest and greatest from Analog Devices, known for their exceptional quality MEMS devices.

    300.00
    Add to Cart
  • triple-axis-magnetometer-breakout-hmc5883l

    ,

    GY-273 Magneto HMC5883L

    This is a breakout board for Honeywell’s HMC5883L, a 3-axis digital compass. Communication with the HMC5883L is simple and all done through an I2C interface, making it Arduino compatible.

    This module can be connected to variety of microprocessors via I2C bus. It comes with a 5V->3.3V regulator, I2C pull-ups on the 3.3V internal power-supply and decoupling capacitors. This module also supports I2C communication at both 3.3V-5V logic level, you can interface this module directly from an Arduino, no pull-ups resistors needed, since they are already included in the module.

    350.00
    Add to Cart