Showing 29–55 of 55 results

View
  • Arduino_flame_sensor_digital_sensor

    ,

    Flame Sensor

    Flare the flame sensor, Infrared receiver module, Ignition source detection module can detect a flame or in a 760 nanometer wavelength of ~ 1100 nm range of the light, lighter flame test distance of 80cm, for the greater flame, the farther the distance test

    245.00
    Add to Cart
  • 31U1UGeDHiL

    ,

    Pressure Sensore MPX5700AP

    The MPX5700AP is a single port, absolute integrated silicon pressure sensor in 6 pin SIP package. This piezoresistive transducer is a state of the art monolithic silicon pressure sensor designed for wide range of applications. This patented, single element transducer combines advanced micromachining techniques, thin film metallization and bipolar processing to provide an accurate and high level analogue output signal that is proportional to applied pressure.

    1,500.00
    Add to Cart
  • MQ-7-MODULE-CARBON-MONOXIDE-GAS-SENSOR

    ,

    MQ-7 Gas Sensor

    This Carbon Monoxide (CO) gas sensor detects the concentrations of CO in the air and ouputs its reading as an analog voltage. The sensor can measure concentrations of 10 to 10,000 ppm.The sensor can operate at temperatures from -10 to 50°C and consumes less than 150 mA at 5 V.

    600.00
    Add to Cart
  • 1

    ,

    2way IR Avoidance Sensor

    2-way Obstacle Avoidance Module Infrared Reflective Sensor Module

    Each one-way infrared sensor continuously emits infrared emission tube, when no infrared rays emitted or reflected back but the strength is not large enough, the infrared receiver has been in the off state, TTL output terminal of the module is high level, the corresponding indicator LED remains off state; occurs when an object is detected within the detection range, infrared is reflected back and the intensity is large enough, infrared receiver is turned on, then the TTL output of the module is low, indicating diode is lit.

    100.00
    Add to Cart
  • cerrent_sensor_copy

    ,

    Current Sensor ACS712-30A

    This module is based on the ACS712ELC-30A integrated circuit, a high performance hall current sensor.

    250.00
    Add to Cart
  • pir_sensor_module

    ,

    HC-SR501 PIR Sensor

    HC-SR501 is based on infrared technology, automatic control module, using Germany imported LHI778 probe design, high sensitivity, high reliability, ultra-low-voltage operating mode, widely used in various auto-sensing electrical equipment, especially for battery-powered automatic controlled products.

    150.00
    Add to Cart
  • sku_133696_1

    ,

    SR04 Ultrasonic Sensor

    The HC-SR04 ultrasonic sensor uses sonar to determine distance to an object like bats do. It offers excellent non-contact range detection with high accuracy and stable readings in an easy-to-use package. From 2cm to 400 cm or 1” to 13 feet. It operation is not affected by sunlight or black material like Sharp rangefinders are (although acoustically soft materials like cloth can be difficult to detect). It comes complete with ultrasonic transmitter and receiver module.

    150.00
    Add to Cart
  • 37-in-1-font-b-Sensors-b-font-Modules-Starter-font-b-Kit-b-font-for

    , ,

    37 in 1 Sensor Module Kit for Arduino And Raspberry Pi

    With this 37 in 1 sensor ultimate package compatible with Arduino & Raspberry Pi , you can do almost all the experiment you can think of , never need to worry about again you don’t have proper materials . this do save you a lot of time .

    2,000.00
    Add to Cart
  • tempSensor

    ,

    18B20 Temperature Module

    These 3-wire digital temperature sensors are fairly precise (±0.5°C over much of the range) and can give up to 12 bits of precision from the onboard digital-to-analog converter. They work great with any microcontroller using a single digital pin, and you can even connect multiple ones to the same pin, each one has a unique 64-bit ID burned in at the factory to differentiate them. Usable with 3.0-5.0V systems.

    275.00
    Add to Cart
  • 10dofmodule_1

    ,

    10 DOF IMU Sensor

    3 Axis Accelerometer + 3 Axis Gyroscope + 3 Axis Magnetometer + Pressure Sensor on one board i.e.

    ADXL 345+L3G4200D+HMC5883L+BMP085 sensors all in one board. There are also a 2.5V voltage regulator, the logic level converter circuit to make it work under the power of 3V-5V. Thanks to the logic level converter circuit, you can connect it with a 3V-5V MCU directly, just plug and play! Also every interrupt pin of the sensors is leaded out.

    1,850.00
    Add to Cart
  • 08606-03-L

    ,

    Flex Sensor 4.5″

    A simple flex sensor 4.5″ in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol – they claim these sensors were used in the originalNintendo Power Glove.

    The resistance of the flex sensor changes when the metal pads are on the outside of the bend (text on inside of bend)

    2,000.00
    Add to Cart
  • 10245-01

    ,

    Load Sensor – 50kg

    This load sensor, sometimes called a strain gauge, is the same one found in digital bathroom scales . This sensor can measure up to about 110 pounds.

    2,800.00
    Add to Cart
  • DHT11__26715.1343837305.1280.1280

    ,

    DHT11 Temperature & Humidity Sensor

    The DHT11 is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins needed).

    150.00
    Add to Cart
  • Fingerprint Reader-1-600x600

    ,

    Fingerprint Reader UART

    Each person’s fingerprint is unique, just like DNA, you can use fingerprint to replace your key, or lock your computer with fingerprint. Adding fingerprint to your project makes it awesome, UART Fingerprint Reader is the new product we want to introduce you!
    UART Fingerprint Reader is a fingerprinting module which integrated STM32F205 as its processor, less power consumption, stable and powerful! It is an intelligent module that provides many functions like fingerprint recording, image processing, eigenvalue extraction, fingerprint matching and searching, etc.
    If you want to communicate with PC, CP2102 USB-TTL module is a good choice.

    Note: Just put finger on the window sightly when register your fingerprint, don’t press the window hardly.
    Note: The on-board mini USB port only used to update module’s firmware, don’t use this port to power module when module is in working mode!

    4,500.00
    Add to Cart
  • IR_Obstacle

    ,

    IR Obstacle Avoidance Sensor

    The sensor module light is adaptable to the environment, the working voltage of 3.3 V to 5 V.
    It has a pair of infrared transmitting and receiving tube, when detecting direction meet with obstacles (reflecting surface), reflected infrared receiving by the tube.

    After the comparator circuit processing, green indicator will light up, at the same time the signal output interface  output a digital signal (a low level signal), can be adjust the detection distance through the potentiometer knob, effective distance range 2 ~ 80 cm, easy to assemble and use. So it can be widely used in robot obstacle avoidance, obstacle avoidance car, line count, and so on many occasions.

    250.00
    Add to Cart
  • MQ-5-1

    ,

    MQ-5 Gas Sensor

    The MQ5 Gas Sensor module is useful for gas leakage detecting. It can detect LPG, i-butane, methane, alcohol, Hydrogen, smoke and so on. The sensitivity can be adjusted using the on-board potentiometer, and you’d use this sensor by reading the analog pin to which it is connected.

    250.00
    Add to Cart
  • 10264-01

    , ,

    Flex Sensor 2.2″

    A simple flex sensor 2.2″ in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol – they claim these sensors were used in the originalNintendo Power Glove. I love the Nintendo Power Glove. It’s so bad!

    The resistance of the flex sensor changes when the metal pads are on the outside of the bend (text on inside of bend).

    1,450.00
    Add to Cart
  • humidity-temperature-sensor-dht22-500x500

    ,

    DHT22 Temperature & Humidity Sensor

    DHT22 output calibrated digital signal. It utilizes exclusive digital-signal-collecting-technique and humidity sensing technology, assuring its reliability and stability.Its sensing elements is connected with 8-bit single-chip computer.

    500.00
    Add to Cart
  • 09375-1

    ,

    Force Sensitive Resistor 0.5

    This is a force sensitive resistor with a round, 0.5″ diameter, sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being applied to the FSR its resistance will be larger than 1MΩ. This FSR can sense applied force anywhere in the range of 100g-10kg.

    1,475.00
    Add to Cart
  • sku_193001_2

    ,

    MQ-135 Gas Sensor

    Its used in air quality control equipments for buildings/offices, are suitable for detecting of NH3,NOx, alcohol, Benzene, smoke,CO2 ,etc.

    780.00
    Add to Cart
  • line-following-sensor (4)-600x600

    Photoelectric line following

    This IR reflective sensor utilizes a TCRT5000 to detect color and distance. It emits IR rays and then detects if it receives the reflection. This sensor is often used in line following robots, auto data logging on utility meters, because this module can sense if a surface is white or black.

    The measuring distance range is from 1mm to 8mm, and the central point is about 2.5mm. There is also an on-board potentiometer to adjust the sensitivity.
    The infrared diode emits the infrared ray continuously when the module connects to the power, when the emitted infrared light has not been reflected or the strength is not big enough, it will be in the off state, at this time, D0 output logic is LOW and the signal indicates LED off.
    350.00
    Add to Cart
  • 411xvoNIUnL_1422595150

    ,

    MQ-2 Smoke Sensor Module

    MQ-2 gas sensor sensitive material used in the clean air low conductivity tin oxide (SnO2). When there is the environment in which the combustible gas sensor, conductivity sensor with increasing concentration of combustible gases in air increases. Using a simple circuit to convert the change in conductivity of the gas concentration corresponding to the output signal. MQ-2 gas sensor high on gas, propane, hydrogen sensitivity of detection of natural gas and other flammable vapors are also very good. This sensor can detect a variety of flammable gas, is a low-cost sensors for a variety of applications.

    200.00
    Add to Cart
  • 09673-01

    ,

    Force Sensitive Resistor – Small

    This is a small force sensitive resistor. It has a 0.16″ (4 mm) diameter active sensing area. This FSR from Interlink Electronics will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being applied to the FSR, its resistance will be larger than 1MΩ, with full pressure applied the resistance will be 2.5kΩ.

    Two pins extend from the bottom of the sensor with 0.1″ pitch making it bread board friendly.

    These sensors are simple to set up and great for sensing pressure, but they aren’t incredibly accurate. Use them to sense if it’s being squeezed, but you may not want to use it as a scale.

    1,500.00
    Add to Cart
  • GY-521_1

    ,

    GY-521 MPU6050 Module 6DOF

    The MPU6050 contains both a 3-Axis Gyroscope and a 3-Axis accelerometer allowing measurements of both independently, but all based around the same axes, thus eliminating the problems of cross-axis errors when using separate devices.

    400.00
    Add to Cart
  • 91450-GY-291-ADXL345-3-Axis-Accelerometer-1200x630w

    ,

    GY-291 ADXL 345

    GY-291 ADXL345 3-Axis Accelerometer is a sensor board based on ADXL345 accelerometer integrated circuit. The ADXL345 is a small, thin, ultralow power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface.

    400.00
    Add to Cart
  • 20150423102824273n548

    ,

    GY-61 ADXL335

    This breakout comes with 3 analog outputs for X, Y and Z axis measurements on a 0.75″x0.75″ breakout board. The ADXL335 is the latest and greatest from Analog Devices, known for their exceptional quality MEMS devices.

    300.00
    Add to Cart
  • triple-axis-magnetometer-breakout-hmc5883l

    ,

    GY-273 Magneto HMC5883L

    This is a breakout board for Honeywell’s HMC5883L, a 3-axis digital compass. Communication with the HMC5883L is simple and all done through an I2C interface, making it Arduino compatible.

    This module can be connected to variety of microprocessors via I2C bus. It comes with a 5V->3.3V regulator, I2C pull-ups on the 3.3V internal power-supply and decoupling capacitors. This module also supports I2C communication at both 3.3V-5V logic level, you can interface this module directly from an Arduino, no pull-ups resistors needed, since they are already included in the module.

    350.00
    Add to Cart